1.0 amp super f ast rectifiers maximum ratings and electrical chara cteristics rating 25 c ambient temperature uniess otherwies specified. single phase half wave, 60hz, resistive or inductive load.for capacitive load, derate current by 20%. type number maximum recurrent peak reverse voltage maximum rms voltage maximum dc blocking voltage maximum average forward rectified current .375"(9.5mm) lead length at t a=55 c fea tures mechanical da t a peak forward surge current, 8.3 ms single half sine-wave superimposed on rated load (jedec method) maximum instantaneous forward voltage at 1.0a maximum dc reverse current t a=25 c at rated dc blocking voltage t a=100 c maximum reverse recovery time (note 1) typical junction capacitance (note 2) 1.0 30 5.0 100 30 -65 +150 a a v ns pf notes: 1. reverse recovery time test condition: if=0.5a, ir=1.0a, irr=0.25a 2. measured at 1mhz and applied reverse voltage of 4.0v d.c. * low forward voltage drop * high current capability * high reliability * high surge current capability * case: molded plastic * epoxy: ul 94v-0 rate flame retardant * lead: axial leads, solderable per mil-std-202, method 208 guranteed * polarity: color band denotes cathode end * mounting position: any 1u1 thru 1u7 0.95 vol t age range 50 to 600 volts current 1.0 ampere 35 1.3 1.7 1u1 1U2 1u3 1u4 1u5 1u6 1u7 units 50 100 150 200 300 400 600 v 50 100 150 200 300 400 600 v 35 70 105 140 210 280 420 v operating and storage t emperature range t j , t stg c r-1 dimensions in inches and (millimeters) .787(20.0) min. .787(20.0) min. .126(3.2) .106(2.7) .025(0.65) .021(0.55) dia. .102(2.6) .091(2.3) dia. a a 88
rating and characteristic curves (1u1 thru 1u7) fig.1- test circuit diagram and reverse recovery time characteristic fig.2-typical forward current a v e r a g e f o r w a r d c u r r e n t , ( a ) fig.6-typical junction capacit ance reverse voltage,(v) 0.2 0.4 0.6 0.8 1.0 1.2 175 150 125 100 75 50 25 0 (+) (+) 25vdc (approx.) ( ) ( ) 10 noninductive 50 noninductive w w pulse generator (note 2) oscilliscope (note 1) 1 non-inductive w notes: 1. rise time= 7ns max., input impedance= 1 megohm.22pf. 2. rise time= 10ns max., source impedance= 50 ohms. +0.5a 0 -0.25a -1.0a | || | | | | | 1cm set time base for 50 / 10ns / cm trr .01 .05 .1 .5 1 5 10 50 100 d.u.t. derating curve 0.1 1.0 .01 10 50 fig.3-typical forward characteristics i n s t a n t a n e o u s f o r w a r d c u r r e n t , ( a ) forward volt age,(v) pulse width 300us 1% duty cycle .4 .6 .8 1.0 1.2 1.4 1.6 1.8 3.0 1 u 5 ~ 1 u 6 1 u 7 1 u 1 ~ 1 u 4 tj=25 c fig.5-maximum non-repetitive forward surge current 10 0 20 30 40 50 number of cycles at 60hz 1 10 5 50 100 tj=25 c 8.3ms single half sine wave jedec method j u n c t i o n c a p a c i t a n c e , ( p f ) single phase half wave 60hz resistive or inductive load 0.375"(9.5mm) lead length p e a k f o r w a r d s u r g e c u r r e n t , ( a ) ambient temperature,( c) 0 0 25 50 75 100 125 150 175 0.1 1.0 .01 10 50 fig.4-typical reverse characteristics 3.0 tj=100 c tj=25 c 0 percent of rated peak reverse vol tage,(%) 20 40 60 80 100 120 140 r e v e r s e l e a k a g e c u r r e n t , ( a ) 89
|
